Category Archives: Bead Kits

Tube Bracelet Instructions

Here are instructions for making the popular “Tube Bracelet” with magnetic closure. Just complete Steps 1-4 below. If you are making one of Anita’s Tube Bracelet Kits, Step 1 has already been done for you.

These instructions have been written for bracelets that have a focal bead in the center. Bracelets with no focal usually have 7 beads (6mm in size) in the middle for the large size; 6 beads (6mm in size) in the middle for the small. You can make Tube Bracelets to fit any wrist size by adding or subtracting beads. These bracelets are meant to fit snug on the wrist.

All components for Tube Bracelets may be purchased separately at Anita’s Beads. See the Tube Bracelet Supplies page.

Your kit contains:
1 24-inch piece of .015 beading wire
2 crimp beads
2 metal wire guards (look like horse shoes)
1 magnet clasp
4 3x2mm rondelle metal beads
4 3mm round metal beads
4 2x38mm metal tubes
6 metal flat heishi spacer beads
10 colored bracelet beads
1 focal bead

You will need the following tools:
Chain nose pliers
Cutters

Step 1) Attach clasp to wire guard with crimp:
Thread the beading wire through one tube of the wire guard from the bottom, and then down the second tube from the top. (Note: if you are unfamiliar with wire guards, they are horse-shoe shaped with a hollow tube portion at both ends connected by an open u-shaped channel between them.)

Move the wire guard to the center of the beading wire. Now slip one ring of your magnet clasp over one end of the beading wire and bring it up into wire guard so it rests around the u-shaped channel. Once the magnet clasp is attached, bring both ends of the beading wire through the crimp. Pinch the two tube portions of the wire guard together so they are touching, and slide the crimp up to meet them.

With your chain nose pliers, flatten the crimp so it makes secure contact to hold the wires. For the best appearance, there should be no space between the wire guard and the flattened crimp. Make sure you do not compress the tiny tubes of the wire guard as you flatten the crimp.

Step 2) String on beads:
Holding the two wires together, string one colored bracelet bead, then one metal rondelle, and then one 3mm round metal bead and slide them up to the crimp. Now split the wires and string one metal tube onto each one and slide them up to the 3mm round metal bead.

Hold the two wires together again and string on one 3mm round metal bead, one metal rondelle, one bracelet bead, and one heishi. Continue to alternate bracelet beads and heishi for a total of two, three, or four sets. Then add the focal bead, followed by enough bracelet beads and heishi to match the first side, ending with a bracelet bead.

You can adjust the size of your bracelet by the number of beads added in the center on either side of the focal bead.

String on a rondelle metal bead directly after the last bracelet bead, and then string on a metal 3mm round. Now split the wires again and string one metal tube onto each.

The bring the wires together again and string on one 3mm round bead, one rondelle, one colored bracelet bead, and finally, the second crimp.

Step 3) Add second wire guard and attach to clasp:
Make sure all beads are strung evenly and without spaces, showing bare wire as little as is possible. Take the two wires coming out of the second crimp and feed them up through one side of the second wire guard, across the top of the wire guard, and down through the second side.

Now slip the second ring of your magnet clasp over the piece of beading wire that you just fed through the second side of the wire guard and bring it up into wire guard so it rests around the u-shaped channel. Once the magnet clasp is attached, bring the ends of the beading wire back down through the crimp and the colored bracelet bead. Pinch the two tube portions of the wire guard together so they are touching.

Keeping the crimp in position against the last colored bracelet bead, pull the tails of the wires running through the wire guard until the gap is eliminated between the crimp and the wire guard. If you can, insert the two tails through the last bead before the crimp as well.

With your chain nose pliers, flatten the crimp so it makes secure contact to hold the wires. For the best appearance, there should be no space between the wire guard and the flattened crimp. Make sure you do not compress the tiny tubes of the wire guard as you flatten the crimp.

Step 4) Trim wires:
Carefully trim off the two short pieces as close as you can. Your tube bracelet is now complete.

Visit Anita’s Beads and ask to see a demonstration at the counter if you need help.

Here are links to additional items related to Tube Bracelets: Tube Bracelet SuppliesCrystal Beads for Birthdays

Daily Bracelet No. 102

a11

Daily Bracelet No. 102 features Czech glass beads and crystal bicones on Antique Brass.

Finished Bracelet – $45.00     Bead Kit – OUT of STOCK

Metal components for this project must be purchased separately. Combine your Bead Kit with one of Anita’s Daily Bracelet Metal Kits to make a complete bracelet.

To order, contact Anita by phone 603-522-6529 or email anitaNH@roadrunner.com

Daily Bracelet No. 101

a12

Daily Bracelet No. 101 features Czech glass beads and crystal bicones on Antique Brass.

Finished Bracelet – $45.00     Bead Kit – $7.50

Metal components for this project must be purchased separately. Combine your Bead Kit with one of Anita’s Daily Bracelet Metal Kits to make a complete bracelet.

To order, contact Anita by phone 603-522-6529 or email anitaNH@roadrunner.com

Daily Bracelet No. 89

a14

Daily Bracelet No. 89 features Czech glass beads and crystal bicones on Antique Brass.

Finished Bracelet – $45.00     Bead Kit – OUT of STOCK

Metal components for this project must be purchased separately. Combine your Bead Kit with one of Anita’s Daily Bracelet Metal Kits to make a complete bracelet.

To order, contact Anita by phone 603-522-6529 or email anitaNH@roadrunner.com

Daily Bracelet No. 90

a10

Daily Bracelet No. 90 features Czech glass beads and crystal bicones on Gunmetal.

Finished Bracelet – $45.00     Bead Kit – OUT of STOCK

Metal components for this project must be purchased separately. Combine your Bead Kit with one of Anita’s Daily Bracelet Metal Kits to make a complete bracelet.

To order, contact Anita by phone 603-522-6529 or email anitaNH@roadrunner.com

Daily Bracelet No. 100

a7

Daily Bracelet No. 100 features Czech glass beads, glass pearls and crystal bicones on Antique Brass.

Finished Bracelet – $45.00     Bead Kit – $7.50

Metal components for this project must be purchased separately. Combine your Bead Kit with one of Anita’s Daily Bracelet Metal Kits to make a complete bracelet.

To order, contact Anita by phone 603-522-6529 or email anitaNH@roadrunner.com

Daily Bracelet No. 95

a2

Daily Bracelet No. 49 features Czech glass beads and crystal bicones on Antique Brass.

Finished Bracelet – $45.00     Bead Kit – $10.50

Metal components for this project must be purchased separately. Combine your Bead Kit with one of Anita’s Daily Bracelet Metal Kits to make a complete bracelet.

To order, contact Anita by phone 603-522-6529 or email anitaNH@roadrunner.com

Daily Bracelet No. 94

11113

Daily Bracelet No. 94 features Czech glass beads, glass pearls and crystal bicones on Antique Brass.

Finished Bracelet – $45.00     Bead Kit – $9.75

Metal components for this project must be purchased separately. Combine your Bead Kit with one of Anita’s Daily Bracelet Metal Kits to make a complete bracelet.

To order, contact Anita by phone 603-522-6529 or email anitaNH@roadrunner.com

 

Daily Bracelet No. 98

a5

Daily Bracelet No. 98 features Czech glass beads and crystal bicones on Antique Brass.

Finished Bracelet – $45.00     Bead Kit – $9.50

Metal components for this project must be purchased separately. Combine your Bead Kit with one of Anita’s Daily Bracelet Metal Kits to make a complete bracelet.

To order, contact Anita by phone 603-522-6529 or email anitaNH@roadrunner.com

Daily Bracelet No. 99

a6

Daily Bracelet No. 99 features Czech glass beads and crystal bicones on Antique Brass.

Finished Bracelet – $45.00     Bead Kit – $9.95

Metal components for this project must be purchased separately. Combine your Bead Kit with one of Anita’s Daily Bracelet Metal Kits to make a complete bracelet.

To order, contact Anita by phone 603-522-6529 or email anitaNH@roadrunner.com